Understanding Plumber's Essentials for Bathtub Installation
Understanding Plumber's Essentials for Bathtub Installation
Blog Article
Each person will have his or her own rationale on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't exactly brain surgery, yet it does call for solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably challenging job. If the old tub is easily available, the job can move immediately; if you have to open up a wall to remove the old tub and also place the new tub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to move out the old tub as well as embeded in the new one. Make sure you have qualified yourself for the task as well as are comfortable attempting it. Instead of hiring a specialist to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This short article will certainly help you set up a new tub in your bathroom if you have actually currently gotten a brand-new bathtub as well as don't require to change the plan of your previous water supply pipes.
Your devices as well as material list must make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is detach the supply of water. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. When the supply pipes have been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bathtub up until the spirit level checks out degree.
To install faucets, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Switch on the water and also examine all joints as well as brand-new pipework for leakages and tighten them if essential. Load the bath tub as well as also check the overflow outlet as well as the normal outlet for leaks.
Lastly, fix the bathroom paneling as described in the producer's user's manual. Tiling as well as sealing around the tub should wait up until the tub has been used a minimum of when as this will settle it into its last position.
Preparing for the Installment
To start with, the supporting framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets making use of 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a rigid seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, bring about problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components as well as installations. They are sold in tubes as well as cartridges, and are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealer can crack fairly early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I imagined sharing that excerpt was essential. Those who liked our blog post kindly do not forget to share it. I thank you for reading our article about Installing A Bathtub.
Customer Reviews Report this page